The blood is teste… A decrease of the total concentration of copper below 0.01 M results in the area of stability of CuCl2−(aq). Conductivities range from (10−10…10−8 [Ω cm]−1) with nylon and polyester. W. G. Mumme, R. W. Gable, V. Petříček, Canadian Mineralogist; (2012); 50; 423-430. Consequently, the stability region of bornite in the summer season (25 °C) will be narrower than in the winter season, as the ranges ∆pH and ∆Eh decrease with rising temperature in the series of −5, 5 and 25 °C. One typical series of reactions that occur under oxidizing conditions and at high temperatures is shown below: FIGURE 15.4. The equilibrium diagrams of the Cu–S–Cl–H2O system at temperatures of 25, 100 and 150 °C are shown in Fig. Copper sulfides can be classified into three groups: Monosulfides, 1.6 ≤ Cu/S ≤ 2: their crystal structures consist of isolated sulfide anions that are closely related to either hcp or fcc lattices, without any direct S-S bonds. 4 FIRST AID MEASURES. Prominent copper sulfide minerals include Cu2S and CuS. The maximum number of stages was determined based on the estimated stage recoveries and the bounds on global recoveries, which resulted in three cleaner stages and one scavenger stage. Certain metal salts like copper sulphide and copper iodide are predominantly utilised for electrically conductive coatings on fibres, as they are easily processable using ordinary textile technology. 8. Copper sulfate solutions may serve as an antiseptic and as a source for depositing copper on metals. In chemistry, a "binary copper sulfide" is any binary chemical compound of the elements copper and sulfur. Ingredient: Copper (II) Sulfide. The input is high-purity cobalt sulfate electrolyte ~20 g/L Co2+. Therefore, the Me–S–Cl–H2O system is also a subject of theoretical studies, although not so frequently as the Me–S–H2O systems [72–74]. Copper sulfides describe a family of chemical compounds and minerals with the formula CuxSy. From the practical viewpoint in leaching, these equilibrium systems are used for theoretical examination of leaching of copper sulphides or copper and iron in the solutions of sulphuric acid, or using iron-sulphide, this is a relatively frequent case and is also utilised in industry, either for pressure leaching or leaching in normal conditions. Oxide concentrate: 20% Cu, 1.3% Co (60% Cu recovery, 40% Co recovery). CU-FES-02-C , CU-FES-03-C , CU-FES-04-C , CU-FES-05-C CAS #: 1308-56-1 Relevant identified uses of the substance: Scientific research and development Supplier details: American Elements 10884 Weyburn Ave. It has a narrow range of stoichiometry ranging from Cu1.997S to Cu2.000S. Deposition of slags of the presented mineral composition in the environment may produce certain effects in surface and/or ground waters. Elemental copper found in nature can be leached by either oxygen or ferric ion: All copper sulfides require the presence of Fe3+ and O2 as oxidizing agents for leaching to occur. Whatever their source, copper sulfides vary widely in composition with 0.5 ≤ Cu/S ≤ 2, including numerous non-stoichiometric compounds. 5.15. The anodes are dissolved to the point at which they start to fall apart. Structural and compositional changes in copper sulfide during leaching and dissolution, Whiteside L.S, Goble R.J, The Canadian Mineralogist; (1986);. Investigations of covellite (CuS) indicate that there are other metastable Cu-S phases still to be fully characterised.[1]. If at room temperature the highest stability was shown by CuCl32−(aq), at higher temperatures it is CuCl2−(aq). Substances containing chlorine in the equilibrium system Cu-S-Cl-H2O. Copper sulfate is an eff… The net-smelter-return formula is used here: where I is the income per year, W is the mass flow of the concentrate, p is the fraction of metal paid, g is the mineral grade concentrate, u is the grade deduction, q is the price of metal, Rfc is the refinery change, Trc is the treatment change, and H is the number of hours per year of plant operation when the mass flows are in tons per hour. Zdzisław, in Reference Module in Materials Science and Materials Engineering, 2017. [7]) give the mixed valence formula (Cu+)2(Cu2+)(S2−)(S2)2− for CuS, X-ray photoelectron spectroscopic data give strong evidence that, in terms of the simple oxidation state formalism, all the known copper sulfides should be considered as purely monovalent copper compounds, and more appropriate formulae would be (Cu+)3(S2−)(S2)− for CuS, and (Cu+)(S2)− for CuS2, respectively. The issue of the valence of copper in sulfides (as well as selenides and tellurides) continues to be revisited in the literature.